Mô tả sản phẩm
Photoelectric sensors
Features
| Sensor/ detection principle | Photoelectric retro-reflective sensor, autocollimation |
| Dimensions (W x H x D) | 12.2 mm x 52.2 mm x 23.6 mm |
| Housing design (light emission) | Rectangular |
| Mounting hole | M3 |
| Sensing range max. | 0 m … 3.5 m 1) |
| Sensing range | 0 m … 2.2 m 1) |
| Type of light | Visible red light |
| Light source | Laser 2) |
| Light spot size (distance) | ? 0.4 mm (60 mm) |
| Wave length | 650 nm |
| Laser class | 1 (IEC 60825-1 / CDRH 21 CFR 1040.10 & 1040.11) |
| Adjustment |
IO-Link Single teach-in button |
| Pin 2 configuration | External input, Teach-in input, Sender off input, Detection output, logic output, alarm output quality of run |
| Diagnosis | Quality of run, Quality of teach-in |
| AutoAdapt | ? |
| Special applications | Detecting small objects, Detecting transparent objects |
- 1) Reflective tape REF-AC1000.2) Average service life: 50,000 h at TU = +25 ?C.
Mechanics/electronics
| Supply voltage | 10 V DC … 30 V DC 1) |
| Ripple | < 5 Vpp 2) |
| Power consumption | 30 mA 3) |
| Switching output | PNP 4) |
| Output function | Complementary |
| Switching mode | Light/dark switching 4) |
| Output current Imax. | ? 100 mA |
| Response time | ? 0.5 ms 5) |
| Response time Q/ on Pin 2 | 300 ?s … 450 ?s 5) 6) |
| Switching frequency | 1,000 Hz 7) |
| Switching frequency Q / to pin 2 | ? 1,000 Hz 8) |
| Connection type | Male connector M12, 4-pin |
| Circuit protection |
A 9) B 10) C 11) |
| Protection class | III |
| Weight | 13 g |
| Polarisation filter | ? |
| IO-Link | ? |
| Housing material | Plastic, VISTAL? |
| Optics material | Plastic, PMMA |
| Enclosure rating |
IP66 IP67 IP69K |
| Special feature | Detecting transparent objects |
| Ambient operating temperature | ?10 ?C … +50 ?C |
| Ambient operating temperature extended | ?30 ?C … +55 ?C 12) 13) |
| Ambient storage temperature | ?30 ?C … +70 ?C |
| UL File No. | NRKH.E181493 |
| Repeatability Q/ on Pin 2: | 150 ?s 6) |
- 1) Limit values when operated in short-circuit protected network: max. 8 A.2) May not exceed or fall below Uv tolerances.3) Without load.4) Q = light switching.5) Signal transit time with resistive load.6) Valid for Q on Pin2, if configured with software.7) With light/dark ratio 1:1.8) With light / dark ratio 1:1, valid for Q on Pin2, if configured with software.9) A = VS connections reverse-polarity protected.10) B = inputs and output reverse-polarity protected.11) C = interference suppression.12) As of Ta = 50 ?C, a max. supply voltage Vmax. = 24 V and a max. load current Imax. = 50 mA is permitted.13) Operation below Tu ?10 ?C is possible if the sensor is already switched on at Tu > ?10 ?C, then cools down, and the supply voltage is subsequently not switched off. Switching on below Tu ?10 ?C is not permissible.
Classifications
| ECl@ss 5.0 | 27270902 |
| ECl@ss 5.1.4 | 27270902 |
| ECl@ss 6.0 | 27270902 |
| ECl@ss 6.2 | 27270902 |
| ECl@ss 7.0 | 27270902 |
| ECl@ss 8.0 | 27270902 |
| ECl@ss 8.1 | 27270902 |
| ECl@ss 9.0 | 27270902 |
| ETIM 5.0 | EC002717 |
| ETIM 6.0 | EC002717 |
| UNSPSC 16.0901 | 39121528 |
Smart Task
| Smart Task name | Base logics |
| Logic function |
Direct AND OR WINDOW Hysteresis |
| Timer function |
Deactivated On delay Off delay ON and OFF delay Impulse (one shot) |
| Inverter | Yes |
| Switching frequency |
SIO Direct: 1000 Hz 1) SIO Logic: 1000 Hz 2) IOL: 900 Hz 3) |
| Response time |
SIO Direct: 300 ?s … 450 ?s 1) SIO Logic: 500 ?s … 600 ?s 2) IOL: 500 ?s … 900 ?s 3) |
| Repeatability |
SIO Direct: 150 ?s 1) SIO Logic: 150 ?s 2) IOL: 400 ?s 3) |
| Switching signal QL1 | Switching output |
| Switching signal QL2 | Switching output |
- 1) SIO Direct: sensor operation in standard I/O mode without IO-Link communication and without using internal sensor logic or time parameters (set to “direct”/”deactivated”).2) SIO Logic: Sensor operation in standard I/O mode without IO-Link communication. Sensor-internal logic or timing parameters plus Automation Functions used.3) IOL: Sensor operation with full IO-Link communication and usage of logic, timing and Automation Function parameters.
Communication interface
| Communication interface | IO-Link V1.1 |
| Communication Interface detail | COM2 (38,4 kBaud) |
| Cycle time | 2.3 ms |
| Process data length | 16 Bit |
| Process data structure |
Bit 0 = switching signal QL1 Bit 1 = switching signal QL2 Bit 2 … 15 = empty |
