Mô tả sản phẩm
Proximity sensors
Features
| Housing | Rectangular |
| Dimensions (W x H x D) | 10 mm x 28 mm x 16 mm |
| Sensing range Sn | 0 mm … 3 mm 1) |
| Safe sensing range Sa | 2.43 mm |
| Number of switching points | Up to 4 adjustable switching points or windows |
| Switching modes | Single point, Window mode, Two point mode, Visual adjustment indicator |
| Switching frequency Qint.1 / Qint.2 on Pin2 | 1,000 Hz |
| Installation type | Flush |
| Connection type | Cable with M12 male connector, 4-pin, 0.2 m 2) |
| Switching output | PNP |
| Output Q/C | Switching output or IO-Link mode |
| Output MFC | Switching output or input |
| Output function | NC / NO |
| Output characteristic | Programmable |
| Electrical wiring | DC 4-wire |
| Enclosure rating | IP68 3) |
| Special features | Smart Task |
| Diagnosis | Chip temperature |
| Pin 2 configuration | External input, Teach-in, switching signal |
- 1) Adjustable.2) With gold plated contact pins.3) According to EN 60529.
Mechanics/electronics
| Supply voltage | 10 V DC … 30 V DC 1) |
| Ripple | ? 10 % |
| Voltage drop | ? 2 V 2) |
| Current consumption | 35 mA 3) |
| Hysteresis | Programmable 4) |
| Reproducibility | ? 5 % 5) 6) |
| Temperature drift (of Sr) | ? 10 % |
| EMC | According to EN 60947-5-2 |
| Continuous current Ia | ? 200 mA 7) |
| Short-circuit protection | ? |
| Reverse polarity protection | ? |
| Power-up pulse protection | ? |
| Shock and vibration resistance | 30 g, 11 ms / 10 … 55 Hz, 1 mm |
| Ambient operating temperature | ?25 ?C … +75 ?C |
| Housing material | Plastic, VISTAL? |
| Sensing face material | Plastic, VISTAL? |
| Tightening torque, max. | < 1 Nm |
| Teach-in accuracy | +/- 3% of Sr |
| Resolution, typical (range) | 20 ?m (0 mm … 3 mm) |
| Resolution, maximum (area) | 40 ?m (0 mm … 3 mm) |
- 1) IO-Link mode: 18 VDC … 30 VDC.2) At Ia max.3) Without load.4) To comply with EN 60947-5-2, a hysteresis of approx. 10% must be set.5) Ub and Ta constant.6) Of Sr.7) 200 mA total for both switching outputs.
Reference values
| Note | Reference value in Digits for switching point in mm stored in the sensor |
| Reference value 1 | 3 mm |
| Reference value 2 | 2 mm |
| Reference value 3 | 1 mm |
| Reference value 4 | 0.5 mm |
Reduction factors
| Stainless steel (V2A, 304) | Approx. 0.7 |
| Aluminum (Al) | Approx. 0.4 |
| Copper (Cu) | Approx. 0.3 |
| Brass (Br) | Approx. 0.5 |
Installation note
| Remark | Associated graphic see “Installation” |
| A | 0 mm |
| B | 10 mm |
| C | 10.3 mm |
| D | 9 mm |
| E | 0 mm |
| F | 24 mm |
| G | 0 mm |
Classifications
| ECl@ss 5.0 | 27270101 |
| ECl@ss 5.1.4 | 27270101 |
| ECl@ss 6.0 | 27270101 |
| ECl@ss 6.2 | 27270101 |
| ECl@ss 7.0 | 27270101 |
| ECl@ss 8.0 | 27270101 |
| ECl@ss 8.1 | 27270101 |
| ECl@ss 9.0 | 27270101 |
| ETIM 5.0 | EC002714 |
| ETIM 6.0 | EC002714 |
| UNSPSC 16.0901 | 39122230 |
Smart Task
| Smart Task name | Counter + debouncing |
| Logic function |
Window Hysteresis Direct |
| Timer function |
Deactivated On delay Off delay ON and OFF delay Impulse (one shot) |
| Inverter | Adjustable |
| Maximum counting frequency |
SIO Logic: 1000 Hz 1) IOL: 1000 Hz 2) |
| Counter reset |
SIO Logic: 500 ?s 1) IOL: — 2) |
| Min. Time between two process events (switches) |
SIO Logic: 0.5 ms 1) IOL: 0.5 ms 2) |
| Debounce time max. |
SIO Logic: 30 s 1) IOL: 30 s 2) |
| Switching signal QL1 | Output type (dependant on the adjusted threshold) |
| Switching signal QL2 | Output type (dependant on the adjusted threshold) |
| Measuring value | Counting value |
- 1) SIO Logic: Sensor operation in standard I/O mode without IO-Link communication. Sensor-internal logic or timing parameters plus Automation Functions used.2) IOL: Sensor operation with full IO-Link communication and usage of logic, timing and Automation Function parameters.
Communication interface
| Communication interface | IO-Link V1.1 |
| Communication Interface detail | COM2 (38,4 kBaud) |
| Cycle time | 5 ms |
| Process data length | 32 Bit |
| Process data structure |
Bit 0 = switching signal QL1 Bit 1 = switching signal QL2 Bit 2 = switching signal QInt3 Bit 3 = switching signal QInt4 Bit 18 … 31 = counting value |
| Factory setting |
Switching Point 1: reference value 1 Output: normally open Pin 2 configuration: input |
