Mô tả sản phẩm
Encoders
Performance
| Linear resolution | 0.125 mm/pulse to 304.8 mm/pulse (type-dependent) |
| Pulses per revolution | 1 … 1500 1) |
| Measuring step | 90? electric/pulses per revolution |
| Measuring step deviation | ? 18?, / pulses per revolution |
| Error limits | Measuring step deviation x 3 |
| Duty cycle | ? 0.5 ? 5 % |
| Initialization time | < 5 ms 2) |
- 1) Available pulses per revolution see type code.2) Valid positional data can be read once this time has elapsed.
Electrical data
| Electrical interface | 4.75 V … 30 V, TTL/HTL DIP switch, selectable output 1) | ||||||||
| Connection type | Male connector, universal 2) | ||||||||
|
|||||||||
| Power consumption max. without load | ? 1.25 W | ||||||||
| Load current max. | ? 30 mA, per channel | ||||||||
| Maximum output frequency | 60 kHz | ||||||||
| Reference signal, number | 1 | ||||||||
| Reference signal, position | 180?, electric, gated with A | ||||||||
| Reverse polarity protection | ? | ||||||||
| Short-circuit protection of the outputs | ? | ||||||||
| MTTFd: mean time to dangerous failure | 275 years (EN ISO 13849-1) 3) | ||||||||
- 1) The output is not selectable for DIP switch configurations E, F, and G. The output voltage value is dependent on the supply voltage.2) The universal connection is rotatable so that it is possible to position the conector in the radial or axial direction.3) This product is a standard product and does not constitute a safety component as defined in the Machinery Directive. Calculation based on nominal load of components, average ambient temperature 40?C, frequency of use 8760 h/a. All electronic failures are considered hazardous. For more information, see document no. 8015532.
Mechanical data
| Measuring wheel circumference | 12 ? | ||||||||||
| Measuring wheel surface | Smooth plastic (urethane) 1) | ||||||||||
| Spring arm design | Without mount | ||||||||||
| Mass | 0.9 kg 2) | ||||||||||
|
|||||||||||
|
|||||||||||
| Start up torque | 0.5 Ncm | ||||||||||
| Operating torque | 0.4 Ncm | ||||||||||
| Operating speed | 1,500 min?? | ||||||||||
| Bearing lifetime | 3.6 x 10^9 revolutions | ||||||||||
| Maximum travel/deflection of spring arm | 40 mm 3) | ||||||||||
| Recommended pretension | 20 mm 3) | ||||||||||
| Max. permissible working area for the spring (continuous operation) | ? 10 mm | ||||||||||
- 1) The surface of a measuring wheel is subject to wear. This depends on contact pressure, acceleration behavior in the application, traversing speed, measurement surface, mechanical alignment of the measuring wheel, temperature, and ambient conditions. We recommend you regularly check the condition of the measuring wheel and replace as required.2) Based on an encoder with a plug connector output and urethane rollers, no mounting necessary (arm mount).3) Only applies to variants with spring arm mounting.
Ambient data
| EMC | According to EN 61000-6-2 and EN 61000-6-3 |
| Enclosure rating | IP65 1) |
| Permissible relative humidity | 90 % (condensation of the optical scanning not permitted) |
| Working temperature range | ?30 ?C … +70 ?C |
| Storage temperature range | ?40 ?C … +75 ?C |
- 1) When the mating connector is installed and the DIP switch door is sealed with the encoder housing.
Classifications
| ECl@ss 5.0 | 27270501 |
| ECl@ss 5.1.4 | 27270501 |
| ECl@ss 6.0 | 27270590 |
| ECl@ss 6.2 | 27270590 |
| ECl@ss 7.0 | 27270501 |
| ECl@ss 8.0 | 27270501 |
| ECl@ss 8.1 | 27270501 |
| ECl@ss 9.0 | 27270501 |
| ETIM 5.0 | EC001486 |
| ETIM 6.0 | EC001486 |
| UNSPSC 16.0901 | 41112113 |
